Garage Door Repair Pros

Unclaimed

This business has not yet been claimed by the owner or a representative. Claim this business

About

We are the best garage door professionals and repair work teams in the Randburg area. Garage Door Repair Pros has a group in Linden - Randburg. We are specialists in assisting you with Garage Door Repairs and installations in Gauteng. What makes us stick out is our speedy 24 hr expert service - economical rates and call out service fee - city to you in gauteng we are the city pros - we bring a sufficient stock of garage door spares.



Our professionals remain in your area to assistance you with your garage door repair work or new installation. We service both house and commercial homeowners. Call us and we can go out within an hour or two if you reside in the following locations:



Jukskei Park

Bromhof

Ferndale

Blairgowrie

Cresta

Northriding

Plus all other regions within 100kms of Randburg

Based in 38 7th Street, Linden, Johannesburg, 2129, we can assist you quick and efficiently. You can call us on 074 471 1979 or email us on randburg@garagedoorpros.co.za



If you have a garage door that is stuck? Your issue is our priority! Give us a call whenever of the day or night and we can aid you get your garage door brought back and fixed very first time and without delay



When your garage door unexpectedly stops operating correctly, the reason for the problem is generally pretty easy to understand.



Here are the most common issues, give us a call and we can assist you to do the garage door repair.



Neither the Remote Control nor the Wall Switch Operates the Opener.

When the garage door doesn't spending plan all when the remote or wall change pressed, it's nearly specific the power source has been interrupted in some way.



Similar to many such problems, the most common problem is the most basic one-- the motor system has been unplugged. Check the outlet where the door opening is plugged in and ensure the cable is plugged in all the method.



It's also possible that the breaker, fuse, or GFCI managing the door opener circuit has tripped or stressed out. If you find that other lights or electrical circuits in the garage aren't operating, this is the likely cause, and you'll require to reset the breaker or GFCI or change the burned-out fuse. If the breaker or GFCI is tripping repeatedly, it's a sign that there is a short circuit someplace in the system-- possibly even the garage door opener itself.



Lastly, it's possible the garage door opener's motor has burned out and isn't running at all. This is an issue that will need you (or a service person) to change it.



The Garage Door Won't Operate With the Remote Control or Keypad.

There are numerous possible options when a remote control or mounted keypad stops operating the opener:



1. Move closer to the door. It's possible you are out of series of the antenna inside the garage. Modern garage door openers are essentially small radios that operate at about 315mH, and a couple of feet of additional distance can impact the signal.



2. Make sure that the antenna on the motor unit is hanging downward and is not harmed in any way.



3. If the door works fine with the wall switch, it's likely the battery requires changing in the remote control or keypad.



4. Reprogram the push-button control or keypad. The delicate electronic devices in can in some cases lose their programs and might require to be reset. Each garage door opener has a slightly different technique of reprogramming, so speak with the directions or look online for details how this is provided for your particular opener.



Garage Door Won't Close All the Way

If the garage door opens correctly however fails to close totally, there may be among 3 common causes:



1. The close-limit switch might need adjusting. Your garage door has set-limit switches that advise the motor when to stop running-- both when it is opening, and when it is closing. If the close-limit switch is set wrong, it might prevent the door from closing It can likewise trigger the opener to reverse or pull back up when you try to close it.



The close-limit switch is a safety measure that keeps individuals from being struck and having the door close on them-- it is a necessary and required device for all garage door openers. Adjusting the limit switch will stop your garage door from acting unpredictably.



Various garage doors have different means of changing the set-limit switches, however it is normally a screw feature on the motor unit that is relied on change how far the door comes down.



2. The safety sensing units may need change or adjustment. Near the bottom of the door track on both sides are electronic eyes that require a clear line of view in between them. If the sightlines are clear between the eyes, the door will close smoothly all the way to the floor. Nevertheless, if anything is blocking the sightline, or if the brackets holding the electronic eyes are out of positioning, the door will fail to descend all the way. In many cases, the door will stop or reverse, and lights will flash to tell you there is an issue.



Make sure there is absolutely nothing obstructing the sight course between the electronic sensing units. Sometimes, leaves or debris can obstruct the sensing units; it if takes place regularly, it might be that vibrations from the door in the tracks are loosening the brackets holding the sensing units.



3. Less regularly, rusted or damaged rollers can trigger the door to bind in the tracks. Replacing harmed rollers, or lubricating them with silicone lube, can remedy this issue. Often the tracks themselves might move or get bent, which can also cause the problem.



Garage Door Reverses Before Hitting the Floor

Two possible problems can result in a garage door reversing prior to it even touches the floor:



1. Garage door openers have an adjustment screw that manages the closing force-- the pressure with which a door is permitted to descend before the motor switches off. When the door reverses before it even hits the floor, this is typically because the close-force setting needs adjustment.



The friction of the door rollers within the tracks is deceiving the door opener into thinking the door has actually reached the flooring, and the opener needs to be changed for less level of sensitivity.



2. Damaged or rusted rollers can likewise produce extra friction, deceiving the door opener into stopping too soon. Ensure the rollers are in good shape and well lubed to prevent this problem.



Garage Door Reverses Immediately After Touching the Floor

When the garage door instantly leaps up after touching the flooring, this too is a close-limit switch problem.



Adjust the close-limit adjustment screw on the door opener motor in little increments up until the door stops upon touching the floor.



Garage Door Does Not Open Completely

When the garage door rises properly but stops short it is completely open, here are the likely causes:



1. The up-limit switch may need to be approached the motor unit. This switch is generally a simple touch-lever installed on completion of the track near the motor unit, and if it is too far, the motor will stop the door before it totally opens. The option is to move the switch better to the motor unit. This is a rather rare issue, and will generally show itself right away after a new garage door opener is installed.



2. Balky or damaged rollers can likewise trigger the door to stop short of completely opening. Inspect and change harmed rollers, and oil rusty ones.



Garage Door Doesn't Open in Winter

Often a garage door that decreases simply fine will fail to open, specifically in winter.



If this takes place, look for a screw on the motor unit to change the level of sensitivity of the opener. Especially in winter season, when rollers might get stiff, the door opener might be refuse to open. Lubricating rollers can also help with this issue.



Methods for adjusting level of sensitivity vary; so speak with the owner's manual for directions.



Garage Door Opens, however the Motor Won't Stop Running

When this uncommon issue happens, it implies the up-limit switch most likely requires to be moved away from the motor system.



It is uncommon for this problem to suddenly happen; if it occurs at all, it will typically be noticed when you first install the garage door opener.



Offer Garage Door Repair Pros Randburg a call to help you with your repair work.